Beginner's Plumbing: What You Need for Installing a Bathtub
Beginner's Plumbing: What You Need for Installing a Bathtub
Blog Article
Nearly everybody has their own unique rationale on the subject of A Step-by-Step Guide to Installing a Bathtub.
Installing a bathtub isn't specifically rocket science, yet it does need strong plumbing, carpentry, and often, tiling skills. Changing an old bathtub with a brand-new one is additionally a moderately hard task. If the old tub is conveniently obtainable, the job can relocate rapidly; if you have to open up a wall surface to remove the old bathtub as well as place the brand-new bathtub, the job is a lot harder. In either case, the task is within a home handyman's abilities, although you will certainly need a helper to vacate the old tub and also set in the brand-new one. Make sure you have actually certified on your own for the task and also fit trying it. Instead of employing a service provider to take control of a halfway-completed task, it is much better to think about utilizing one before you start. Opportunities are you may need a specialist plumber to make tube links.
This short article will aid you set up a brand-new tub in your restroom if you have actually already bought a brand-new tub and also don't require to change the setup of your previous water system pipes.
Your tools and also material list ought to comprise the following:
Removing Old Touches
If you need to change old faucets with brand-new ones as a part of your setup, after that the first thing you must do is disconnect the water supply. After doing so, activate the taps to drain any type of water continuing to be in the system. The procedure of getting rid of the existing taps can be fairly problematic because of the restricted gain access to that is usually the instance.
Utilize a basin wrench (crowsfoot spanner) or a tap tool to reverse the nut that links the supply pipes to the taps. Have a towel prepared for the remaining water that will certainly originate from the pipes. As soon as the supply pipelines have been gotten rid of, utilize the same device to loosen the nut that holds the faucets onto the bath/basin. You will require to stop the solitary taps from transforming during this procedure. As soon as the faucets have been eliminated, the holes in the bath/basin will certainly have to be cleansed of any kind of old sealing substance.
Before proceeding to fit the brand-new taps, contrast the pipeline connections on the old faucets to the new taps. If the old taps are longer than the brand-new taps, then a shank adapter is needed for the brand-new faucets to fit.
Fitting New Taps
If the tails of the new faucets are plastic, then you will require a plastic connector to avoid damage to the string. One end of the connector fits on the plastic tail of the faucet and the various other end gives a connection to the current supply pipes.
If you require to fit a monobloc, then you will certainly call for reducing couplers, which attaches the 10mm pipeline of the monobloc to the standard 15mm supply pipeline.
Next off, position the tap in the placing opening in the bath/basin making sure that the washers remain in location between the tap and also the sink. Protect the faucet in position with the manufacturer given backnut. When the tap is safely in place, the supply pipelines can be connected to the tails of the faucets. The taps can either be linked by utilizing corrugated copper piping or with typical faucet connectors. The previous kind ought to be attached to the tap ends initially, tightening up only by hand. The supply pipelines can later be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.
Setting up the Tub
Utilizing both wooden boards under its feet, put the bathtub in the needed placement. The wood boards are practical in uniformly spreading the weight of the tub over the area of the boards rather than concentrating all the weight onto 4 little factors.
The following goal is to make sure that the bath tub is leveled all round. This can be attained by checking the level and also changing the feet on the tub until the spirit level reviews degree.
To install taps, fit all-time low of the furthest flexible faucet port to the suitable supply pipeline by making a compression sign up with; then do the very same for the other faucet.
Turn on the supply of water and also inspect all joints and also new pipework for leakages and tighten them if essential. Fill the bath tub and likewise examine the overflow electrical outlet and also the normal electrical outlet for leakages.
Finally, take care of the bath paneling as described in the supplier's user's manual. Tiling as well as sealing around the bathtub should wait till the tub has been used a minimum of once as this will settle it into its last position.
Preparing for the Installation
First of all, the supporting structure supplied with the bath must be fitted (if required) according to the supplier's directions. Next, fit the taps or mixer to the bathtub. When suitable the tap block, it is important to make certain that if the faucet comes with a plastic washer, it is fitted in between the bathroom and also the faucets. On a plastic bath, it is also reasonable to fit a sustaining plate under the faucets system to prevent pressure on the tub.
Fit the versatile tap ports to the bottom of the two taps making use of 2 nuts as well as olives (occasionally supplied with the bathtub). Fit the plug-hole electrical outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet with the hole in the bathroom. Utilize the nut provided by the producer to fit the plug-hole. Check out the plug-hole outlet for an inlet on the side for the overflow pipe.
Next off, fit completion of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which must be fitted inside the bathroom. Ensure you make use of all of the provided washing machines.
Link the catch to the bottom of the waste electrical outlet on the tub by winding the string of the waste outlet with silicone mastic or PTFE tape, and screw on the catch to the outlet. Connect the bottom of the overflow tube in a comparable manner.The bath should currently prepare to be fitted in its final setting.
Tiling Around the Tub
In the location where the bathroom meets the ceramic tile, it is needed to secure the joins with a silicone rubber caulking. This is very important as the installation can move enough to split a rigid seal, creating the water to permeate the wall in between the bathroom as well as the tiling, leading to issues with dampness as well as feasible leakages to the ceiling below.
You can pick from a variety of coloured sealants to blend in your components and also fittings. They are offered in tubes as well as cartridges, and also are capable of sealing gaps as much as a size of 3mm (1/8 inch). If you have a bigger void to load, you can load it with spins of drenched paper or soft rope. Remember to always fill the bathtub with water prior to securing, to permit the activity experienced when the tub is in usage. The sealer can break relatively early if you do not take into account this movement prior to sealing.
Alternatively, ceramic coving or quadrant floor tiles can be made use of to edge the bathroom or shower tray. Plastic strips of coving, which are easy to use and also reduce to size, are additionally conveniently readily available on the marketplace. It is recommended to fit the floor tiles utilizing water-resistant or water-proof adhesive and grout.
How to Install or Replace a Bathtub
Find Your Dimensions
The first step in any bathtub installation or replacement is to select the right size tub for your bathroom. Start by measuring your existing bathtub’s alcove from wall to wall. The standard size for bathtubs is around 5 feet long and 30 or 32 inches wide. Purchase the size that’s closest to your previous tub.
After you’ve measured, you’ll need to figure out what type of tub you need. Face the alcove. If the drain is on the right-hand side, you’ll need a right drain tub. If it’s on the left, get a left drain tub. Easy enough, right?
Disconnect the Water Supply and Drain Assembly
Before you can start on your removal, make sure that you turn off the tub’s water supply. Some bathrooms have a shutoff valve, but if you don’t see one, you’ll need to turn off the supply at your house’s water main. Once the water’s off, open the valves to release any remaining air in the supply lines.
Then, disconnect the tub drain flange. This process varies based on the type of drain you have, but in most cases, you’ll need a drain flange removal tool to perform this task. If you’re feeling handy, you might be able to use a pair of needle-nose pliers to twist and pull the flange.
Now comes the fun part. In order to disconnect the drain assembly, you’ll need to be able to get to the space underneath the tub. You might need to access the tub drain from a crawlspace or a basement. Don’t forget to take a pipe wrench with you, as you’ll need it to loosen the pipe at the connection.
Cut Out the Old Tub
After removing the drainpipe assembly, you can take out the old bathtub. Cut a strip above the tub edge in the wall surrounding the bathtub that's about 6 inches in height. The tools you need here may vary depending on the type of wall surround you have in the alcove. If you’re cutting drywall, use a drywall saw and remove the section of the wall all the way down to the studs. If you have tile, you’ll need to use a grinder with a diamond blade to cut through the grout line. Then, use a chisel to remove the individual tiles. Take care here not to cut through any studs.
Find the tub flange. Remove the screws that attach the flange to the studs in the wall. At this point, the tub should be freed from the wall.
Once you’ve removed the flange, use a utility knife to cut away the caulk between the tub and the floor. When this is done, you should be able to lift the tub up and out of the alcove. Keep in mind that, depending on what it’s made of, the old tub could be tremendously heavy. You should plan to have a friend help you move it just in case.
Install the New Tub
Before you make any adjustments to the area, place the new tub in the alcove to make sure it fits properly and that the tub drain lines up with the P-trap underneath the floor.
Remove it and install a 2 x 4 ledger board. Measure the tub’s flange, then mark that height on the wall. Screw the ledger board to studs in the wall. This will help to support the weight of the tub.
Once the ledger board has been installed, go ahead and secure the drain to the tub. For this step, you’ll need some plumber’s putty. Roll a small amount of putty in your hands and wrap it around the underside of the drain flange. Push the drain into the tub from underneath the tub.
When the drain has been attached, connect the overflow drain. To do this, you’ll place the gasket on the overflow elbow and move it behind the tub. Once that’s on, connect the overflow pipe and the drainpipe, but take care not to overtighten.
Secure the Tub
After the connections are in, it’s time to set the tub in place. Before you start, make sure the flange lines up with the markings you made in Step 4. Because the ledger board holds the tub in place, it’s important that it matches up. If not, you’ll need to remove it and readjust.
Once your measurements line up, attach the flange to the studs on all three sides of the wall. Please note that you should not screw the flange to the wall. Instead, you should use roofing nails because they won’t rust over time. When the tub is in place, install the baseboard and the molding in front of and around the tub.
Repair and finish off the drywall or tile that you cut in Step 3. If you’re installing a fiberglass bath surround, now’s the time to adhere it to the alcove.
Then, enjoy your tub! While all these steps might seem intimidating, removing and installing a new bathtub is a relatively easy DIY project that can be completed in a single day. And now, when you settle in for your next bubbly soak, you can enjoy your bath without the distraction of a tub in disrepair.
https://www.homeserve.com/en-us/blog/how-to/bathtub-replacement/
As a reader on Installing A Bathtub, I think sharing that piece of content was important. Sharing is caring. Helping people is fun. I enjoy reading our article about Installing A Bathtub.
Schedule Your Service Report this page